IROCZONE.COM

new s&w subframe and rust repair

blue89irocz — Fri, 20 Nov 2009 01:06:14 -0500

well, my winter project is to tackle the rust on the car and redo all of the stock-old undercoating underneath. i began by pulling up

Screw/bolt set

torchred — Sat, 14 Nov 2009 04:57:42 -0500

I have a question regarding body work on my IROC. I have taken everything apart, and it's being painted as we speak, however, when i put

Program XM on my 2003 Denali

Erock198 — Thu, 12 Nov 2009 22:10:43 -0500

Does any of you GM techies know how to program the radio? I dont know much about it but I dont want to pay

cant figure it out

irocg — Mon, 09 Nov 2009 21:46:41 -0500

When I start my 87 Iroc it runs great for about 3 minutes then it starts to run like crap..i was thinking it can be

wont start

CDowney — Wed, 04 Nov 2009 16:08:03 -0500

1987 IROC with 5.7L Previous owner changed the relay plugs on drivers side firewall needless to say not sure if he got them

still having low oil pressure HELP

87350tpi — Sun, 01 Nov 2009 15:48:30 -0500

hello y�all, in my previous post i had this problem with the oil pressure, special when its hot, chance the iac valve but nothing happened,

4th gen door handles on a 3rd gen??

nitemare3o5 — Wed, 28 Oct 2009 23:08:28 -0400

Has anybody tried this? When I picked up some seats today the guy did an LS1 swap to his 3rd gen and he said he

305 TPI Torque Sequence

CTC SXE — Sun, 25 Oct 2009 23:32:13 -0400

Do you guys know the torque sequence for a 89 305 tpi cyl. heads. Thanks... a diagram would be helpful if you guys happen

5.7l to a 6.0l(help)

blue89irocz — Sat, 24 Oct 2009 20:40:02 -0400

Im thinking of stroking my 350(l98) i believe i can use a 3-3/4 stroke crank any suggestions for the build heads,cam,intake,ect i would like to

1989 iroc z 5.7l (1le) whats it worth

Aron213 — Fri, 23 Oct 2009 21:14:40 -0400

I have a 1989 iroc z 5.7l 1le i believe thats what it is there was only 111 made in 89 i wanted a

Hey Aron

chevymec — Thu, 22 Oct 2009 21:47:05 -0400

What is you opinion for a dome/dish piston using a set of large port Vortec heads, 206cc version? I have always read that the vortec

l98 tpi 5,7l(400-450hp needed)

87350tpi — Thu, 22 Oct 2009 18:47:18 -0400

Hi i just bought a 89 iroc z it is a police edition with a 5.7l tpi, 700r4,with 2.73 rear end. Im looking

stock valve spring

87350tpi — Tue, 20 Oct 2009 23:51:44 -0400

dose any one know what is the biggest cam u can use on stock springs on a 350

Gear drive.

CTC SXE — Sun, 18 Oct 2009 20:45:29 -0400

I haz a Summit double roller on the car now. Is there any objections to upgrading to a gear drive setup? I know about the

found a car. is it worth it?

irocZ — Sun, 18 Oct 2009 19:49:03 -0400

http://gulfport.craigslist.org/cto/1404722185.html i found this car on craigslist. the ad says 2000 but he has since then lowered it to 1500

85 tpi 305 low oil pressure when its hot

Aron213 — Sun, 18 Oct 2009 15:59:18 -0400

hello everyone, im new here and happy because ive finally found an iroc site, ive a 1985 iroc z, with the 305 and 43k original

No start

87IROCZ — Sat, 17 Oct 2009 18:59:21 -0400

I'm stumped .. any help would be appreciated .. no spark at coil. replaced the coil w/new MSD old MSD as well. I have

Fuel Issue NEED HELP PLEASE

Aron213 — Fri, 16 Oct 2009 20:16:40 -0400

Hey Guy's been a while since I stopped by, I like the new look of the site!!!! Heres my issue and I am truly

How do you...

chevymec — Tue, 13 Oct 2009 22:22:18 -0400

check the pickup on the distributor. ive replaced my coil, ignition switch, battery and still no spark not even to the distributor. i talked to

just getting started. need some advice for the vets

nitemare3o5 — Mon, 12 Oct 2009 23:06:37 -0400

im a newb to the 3rd gen sceen. im currently looking for a strong running iroc z with either the 305 tpi or the 350